Checks 1 and 2: Power and Connections
Where you are: Module 5 — Quick-Win Checks · Lesson 5.1 · Based on Chapter 5 (§5.1–5.2) of Dr. Tahseen Al Doori's Troubleshooting Essentials.
What you'll be able to do
- List the five quick-win checks in the author's order and explain why they come first.
- Carry out the power check (Check 1) from the outside of the equipment, following the supply from socket to device.
- Carry out the connections check (Check 2) for cables, Wi-Fi, Bluetooth, airplane mode and paired accessories.
- Recognise the danger signs that mean you stop troubleshooting and escalate.
Watch: Checks 1 and 2: Power and Connections
The video follows a fictional "completely dead" reception computer on a Monday morning and resolves it in ten minutes with nothing but the first two quick-win checks. As you watch, keep these questions in mind:
- Why does the book insist on these checks even when you are sure they are not the cause?
- In what order would you test the parts of a power supply, from the wall to the device?
- What would make you stop checking and escalate instead?
Why quick wins come first
In Module 4 you learned to define a problem precisely before touching anything. The next stage, still early in Step 2 of the seven-step method (Establish a theory of probable cause), is to rule out the obvious. Chapter 5 of the book observes that a large share of everyday faults is resolved by five basic checks. They take minutes, cost nothing and remove the most common causes from the list. Experienced technicians perform them first, every time, even when they are sure they are not the cause.
That last phrase matters. In Module 2 you met the principle start simple and the common mistake of assuming "it can't be that". Confidence is not evidence. A technician who skips the power check because "obviously it's plugged in" may spend an hour diagnosing a motherboard that was never receiving power.
The five checks, in the author's order, are:
The order is deliberate. It runs from the most physical and quickest (is it switched on?) towards the deeper and slower (are resources exhausted?). Each check also depends on the ones before it: there is no point examining settings on a device that has no power. This lesson covers Checks 1 and 2; Lessons 5.2 and 5.3 cover the rest.
Check 1: Power
The book breaks the power check into three groups of questions:
- Is the device switched on? Are its indicator lights or its display active? Some devices have a separate power switch at the back as well as a button at the front.
- Is the supply reaching it? Is the plug fully inserted, is the wall socket working, and is the power strip switched on?
- Is the battery charged? If you are unsure whether the charger or battery is at fault, try a different charger, a different cable or a different socket.
That third suggestion is your first taste of a Module 6 technique, substitution: swapping a suspect part for one known to work.
Follow the supply from socket to device
A useful habit, which Chapter 8 of the book applies to computers that will not power on, is to treat power as a chain and check it link by link from the source:
| Stage | How to check it from the outside |
|---|---|
| Wall socket | Plug in something you know works, such as a desk lamp or phone charger |
| Power strip | Is its own switch on? Is it plugged into a live socket? |
| Plug and cable | Push both ends fully home, or swap in a known-good cable |
| Charger or power brick | Does it have an indicator light? Is it lit? |
| The device | Any light, fan noise or screen activity? |
The first stage that fails is where the power stops. Notice that you never need a tool or a screwdriver for any of this.
Safety: power checks happen from the outside only. Never open a computer, a charger, a monitor or a power supply to check for power. The book warns that power supplies and monitors can hold dangerous charges even when unplugged. If you notice a burning smell, smoke, sparks, a swollen battery, exposed wiring or water near electricity, stop troubleshooting: switch off at the socket only if it is safe to do so, keep people away and escalate (Chapter 13 lists these as immediate escalation triggers).
Check 2: Connections
Once a device has power, it needs to be connected to the things it works with. The book's connections check asks:
- Are all cables seated firmly at both ends? Do not just look: unplug each cable and reseat it. A connector can appear to be in place while making poor contact.
- Is Wi-Fi or Bluetooth enabled and connected to the correct network or device? Laptops often join a neighbouring or guest network automatically, which looks like "no internet" to the user.
- Is airplane mode off? Airplane mode normally switches off the wireless radios together and is easily switched on by accident with a key combination or a swipe.
- Is the accessory paired and in range? A wireless mouse or headset may have lost its pairing, or may simply be too far from the computer.
Connections covers both data and power cables. A monitor that says "No signal" is usually a connections problem (the video cable), while a monitor showing no light at all is a power problem.
Worked example
(Fictional scenario.) At 08:10 on Monday, reception reports that their desktop PC is "completely dead": no lights, no fan noise, blank monitor. It worked on Friday afternoon. When asked what changed, the receptionist mentions that the office was deep-cleaned over the weekend.
- Check 1, power. The technician plugs a desk lamp into the wall socket: it lights, so the socket is live. The power strip's switch, however, is off, probably knocked during cleaning. Switching it on brings the PC to life.
- Check 2, connections. The PC starts, but the monitor shows "No signal". The video cable at the back of the PC has been pulled half out. Reseating it brings up the sign-in screen.
- Verify. The receptionist signs in and checks a visitor in normally.
- Document. The ticket records two causes (strip switched off, video cable dislodged), the fixes, and a note to the facilities team asking cleaners not to move cables behind desks.
Total time: about ten minutes. Nothing was opened and nothing was replaced. Notice how the "what changed?" question from Module 2 pointed straight at the likely area.
Try it
Goal: practise Checks 1 and 2 safely on equipment you use every day.
- Choose two devices at home or in a lab: one mains-powered (a desktop PC, monitor or printer) and one battery-powered (a laptop, phone or wireless accessory).
- For each, write down the power chain from source to device (for example: socket → strip → plug → charger → laptop).
- Walk the chain and note how you would test each link from the outside: what you would look at, and what known-good item you could swap in.
- List every connection the device depends on (cables at both ends, Wi-Fi network name, Bluetooth pairings, airplane mode).
- Do not open anything, and do not unplug equipment that someone else is using.
You have finished when you have a short written checklist for each device covering every link in its power chain and every connection, with a test for each.
Knowledge check
What is the first of the five quick-win checks in the book's order?
A desktop PC shows no lights. A lamp works in the same wall socket. What should you check next?
A monitor's power light is on, but the screen says 'No signal'. Which quick-win check is most relevant?
While checking a laptop charger you notice the laptop's battery is visibly swollen. What should you do?
Answers explained
- C. The book's order is power, connections, restart, settings and input, then updates and resources. Restart and settings come later; connections is second.
- A. The socket is proven live, so the next link in the chain is the strip and plug. Drivers and passwords are later checks, and opening a power supply is never part of a quick win (and is dangerous).
- B. The monitor has power (its light is on), so the missing signal points to the video cable: a connections problem. Updates are irrelevant here, and nothing yet suggests danger.
- C. A swollen battery is a safety escalation trigger. Pressing it, continuing to charge it or opening the case could cause a fire or injury.
Key takeaways
- Run the five quick-win checks first, in order, every time, even when you are sure they are not the cause.
- Power: follow the supply from socket to device, testing each link with known-good items.
- Connections: reseat every cable at both ends and check Wi-Fi, Bluetooth, airplane mode and pairing.
- Every check is done from the outside; any danger sign means stop and escalate.
Sources
- Dr. Tahseen Al Doori — Troubleshooting Essentials, University Edition (2026), §5.1–5.2 (with cross-references to §2.2, §7.5, §8.1 and §13.1)
