No Power and No Boot
Where you are: Module 8 — Computer and Hardware Troubleshooting · Lesson 8.1 · Based on Chapter 8 (§8.1–8.2) of Dr. Tahseen Al Doori's Troubleshooting Essentials.
What you'll be able to do
- Follow the book's five steps for a computer that will not power on.
- Distinguish a no power fault from a no boot fault.
- Match common boot symptoms to their likely causes and first actions.
- Apply the safety rules before touching the inside of any computer.
Watch: No Power and No Boot
The video starts with two fictional computers that look equally "dead" and shows why they are completely different problems. It traces the supply chain from wall socket to device, then reads the clues a computer gives when it powers on but will not start. Keep these questions in mind:
- What is the first observation that separates no power from no boot?
- Why do you remove accessories before anything else?
- What should you write down when a computer beeps or flashes a light?
Safety first (book, Chapter 8). Before opening any computer: shut down, unplug, remove the battery where possible, press the power button to discharge, and wear an anti-static strap. Do not open equipment under warranty without authorisation. Never open a power supply. A swollen battery, a burning smell, smoke or sparks mean stop, switch off at the source if it is safe to do so, and escalate (Module 13).
Two different problems
A computer that "won't turn on" may be one of two quite different faults:
- No power: nothing happens at all. No fans, no lights, no sound. The fault is somewhere in the chain that delivers electricity to the device.
- No boot: the computer powers on (fans spin, lights glow, perhaps a logo appears) but the operating system never finishes starting. Booting is the start-up process: the firmware tests the hardware, finds the storage device and loads the operating system from it.
The first observation, do fans spin and do lights come on?, decides which half of the problem you are in. This is the half-split idea again.
The computer will not power on (§8.1)
The book gives five steps, in order:
- Check power: the cable, the wall socket, the power strip, the charger light and the battery.
- Disconnect all accessories and external drives, then try again. A faulty accessory can stop a computer from starting.
- For laptops, hold the power button for 15–30 seconds to discharge, then press it once.
- Observe: do fans spin, do lights come on, are there beeps? Record any beep or light pattern and look it up in the manufacturer's documentation.
- For desktops, test the power supply with a known-good unit or a power supply tester.
Notice how the list follows the supply chain from the socket towards the device, simplest and safest checks first. Steps 1 and 2 echo the quick-win checks of Module 5; step 2 is remove-and-restore; step 5 is substitution with a known-good part. Testing a power supply means plugging it into a tester or swapping in a spare: the supply itself is never opened, because it can hold a dangerous charge.
Powers on but does not boot (§8.2)
Once power is confirmed, the computer itself usually tells you what is wrong. Read its messages, lights and sounds:
| Symptom | Likely cause | Action |
|---|---|---|
| No display, fans running | Display, cable, graphics or memory | Test an external monitor; reseat memory |
| Beep codes or flashing lights | Hardware fault reported by firmware | Look up the code; reseat or replace the part |
| "No boot device found" | Storage not detected or boot order wrong | Check firmware (BIOS/UEFI) settings and drive connection |
| Starts, then restarts in a loop | Failed update, corrupt system files | Use safe mode or recovery tools; roll back the update |
| Blue or black error screen | Driver, memory or system fault | Record the stop code; check recent driver changes |
Adapted from the book's §8.2 symptom table.
Key terms:
- Firmware (BIOS/UEFI) is the small program stored on the motherboard that runs first when the computer is switched on. It tests the hardware and chooses which drive to start from (the boot order).
- Beep codes and light codes are the firmware's way of reporting a hardware fault before anything appears on screen. They differ between manufacturers, which is why the book says to look them up in the manufacturer's documentation rather than guess.
- Reseating means removing a part and inserting it again firmly, which cures many loose-connection faults. It requires opening the case, so the safety box applies.
- A stop code is the error code shown on a blue or black error screen; it names the kind of failure and can be researched.
Beyond the book (2026 note): Microsoft's current guidance describes a stop code, such as PAGE_FAULT_IN_NONPAGED_AREA or MEMORY_MANAGEMENT, as appearing at the bottom of the error screen, and also calls it a bug check or blue screen error. For repeated stop-code restarts it recommends removing newly added hardware, starting in safe mode if normal start-up fails, checking Device Manager for devices marked with an exclamation point, keeping about 10–15% of the drive free, installing updates and, if nothing else works, using a restore point. Source: Troubleshooting Windows unexpected restarts and stop code errors — Microsoft Support
Reading the table as a technician
Each row points to the next test. "No display, fans running" is first a display question: connect an external monitor. If the external monitor works, the fault is in the laptop's own screen or its connection; if it does not, memory and graphics become the theories. "No boot device found" is a storage question: does the firmware see the drive at all? If it does not, the drive or its connection is suspect, and if the drive holds important data, Module 8.3's rule applies: protect the data first. A restart loop after an update points to rollback. Always link the symptom to what changed.
Worked example
(Fictional scenario.) A receptionist's desktop PC shows no signs of life on Monday morning.
- Identify: no fans, no lights. Over the weekend the office was cleaned. This is a no power fault.
- Check power: the monitor on the same power strip is also off. The strip's switch was knocked off during cleaning.
- Implement: the strip is switched on; the PC starts normally.
- Verify: the receptionist signs in and opens her usual applications.
- Document: the ticket records the cause, and the strip is moved behind the desk.
Now a second (fictional) case: a laptop powers on, the fan spins, and the screen reads "No boot device found" after the owner dropped it. The firmware does not list the internal drive. The technician does not repeatedly restart it or attempt repairs: the drive may be damaged and holds the owner's thesis. The case is escalated for data recovery with full notes.
Try it
A paper-based diagnosis exercise; do not open any equipment.
For each symptom, write (a) no power or no boot, (b) the likely cause from the book's table, and (c) your first action:
- A laptop shows nothing on screen but its fan runs and the keyboard lights up.
- A desktop beeps three times and shows nothing.
- A PC says "No boot device found" after a new drive was fitted.
- A laptop restarts endlessly after last night's update.
- A desktop shows a blue screen with
MEMORY_MANAGEMENTa few minutes after start-up.
Completion criteria: all five classified correctly, each with a cause and a safe first action taken from the book, and at least one answer that names a recent change.
Knowledge check
A computer shows no fans, no lights and no sound. What should you check first?
A laptop powers on, fans spin, but the screen stays blank. What is a sensible first test?
The message 'No boot device found' most likely means:
A desktop beeps in a pattern at start-up. What does the book advise?
Answers explained — 1: with no signs of life the fault is in the supply chain, so power comes first; boot order, memory and drivers matter only once the machine powers on. 2: a blank screen with fans running points first to the display, and an external monitor tests that quickly; a new power supply or reinstall is unjustified. 3: the book links this message to storage not detected or a wrong boot order, not power, network or display. 4: beep codes are firmware reports that vary by manufacturer, so record and look them up; ignoring them wastes evidence and power supplies are never opened.
Key takeaways
- First decide: no power (nothing happens) or no boot (powers on but does not start).
- No power: trace the supply chain from socket to device, removing accessories along the way.
- No boot: read the codes, lights and messages the system gives, and link them to what changed.
- Shut down, unplug, discharge, wear an anti-static strap, respect the warranty, and never open a power supply.
Sources
- Dr. Tahseen Al Doori — Troubleshooting Essentials, University Edition (2026), §8.1–8.2, Chapter 8 Safety First box, §13.1
- Troubleshooting Windows unexpected restarts and stop code errors — Microsoft Support
