
Toolkit: Half-Split Isolation Worksheet
Toolkit 4 of 10 · Half-Split Isolation Worksheet · Based on §6.1 and §7.3 of Dr. Tahseen Al Doori's Troubleshooting Essentials, University Edition (2026). Worksheet layout by the course.
How to use this sheet
Use the half-split (divide and conquer) method when a fault lies somewhere along a long chain of components or stages, such as a network path or a signal passing through several devices. Divide the chain into two halves and test the point between them. If the first half works, the fault must lie in the second; divide that half again. Each test removes half of the remaining possibilities.
- List every component in order from source to destination in Part 1.
- Work out the maximum number of tests in Part 2.
- Record each test in Part 3: the midpoint you tested, the result, and which half remains.
- Stop when one component remains, then confirm it (for example by substitution with a known-good part).
Part 1 — The chain
Number the components from the source (1) to the destination (n).
| # | Component or stage | # | Component or stage |
|---|---|---|---|
| 1 | 9 | ||
| 2 | 10 | ||
| 3 | 11 | ||
| 4 | 12 | ||
| 5 | 13 | ||
| 6 | 14 | ||
| 7 | 15 | ||
| 8 | 16 |
Source: __________________ Destination: __________________ Number of components (n): ______
Part 2 — Maximum number of tests
Each test halves the remaining possibilities, so the maximum number of tests is the number of times n can be halved until one component remains.
| Components (n) | Maximum tests |
|---|---|
| 2 | 1 |
| 4 | 2 |
| 8 | 3 |
| 16 | 4 |
| 32 | 5 |
| 1,000 | 10 |
For a number between these, round up: for example, 12 components need at most 4 tests.
My chain needs at most ______ tests.
Part 3 — Test record
| Test | Remaining range (from # to #) | Midpoint tested | How tested | Result (pass / fail) | Fault now lies between # and # |
|---|---|---|---|---|---|
| 1 | 1 to n | ||||
| 2 | |||||
| 3 | |||||
| 4 | |||||
| 5 |
Isolated component: __________________
Confirmation test (for example, substitute a known-good part): __________________ Result: ________
Part 4 — The network path as a half-split
The book's five-command connectivity sequence applies the half-split idea to every network fault: each command tests one more part of the path, and the first command that fails shows where the fault lies.
| # | Command (Windows) | What it proves | Result |
|---|---|---|---|
| 1 | ping 127.0.0.1 | The TCP/IP stack works locally | |
| 2 | ipconfig | The device has a valid IP address and gateway | |
| 3 | ping <default gateway> | The device can reach its router | |
| 4 | ping 8.8.8.8 | The device can reach the internet by IP address | |
| 5 | ping <a name, e.g. example.com> | Name resolution (DNS) works |
First step that failed: ______ What this tells me: __________________
Worked illustration
(Fictional scenario.) A laptop on office Wi-Fi cannot open a website. The path has eight stages: 1 laptop, 2 Wi-Fi adapter, 3 access point, 4 switch, 5 router, 6 modem, 7 provider's network, 8 web server. With 8 stages, at most 3 tests are needed.
| Test | Range | Midpoint tested | Result | Fault now lies in |
|---|---|---|---|---|
| 1 | 1–8 | Stage 4: can the laptop reach a device on the switch? (ping the office file server) | Pass | Stages 5–8 |
| 2 | 5–8 | Stage 6: can the laptop reach the modem? (ping the modem's local address) | Pass | Stages 7–8 |
| 3 | 7–8 | Stage 7: does tracert to the web server stop at the first hop beyond the modem? | Replies stop there | Stage 7: the provider's network |
Confirmation: the modem's internet light is red, other websites fail too, and the provider confirms a line fault. The modem's own connection to the line should be part of the provider's check, because test 2 proves only the modem's local side.
Sources
- Dr. Tahseen Al Doori — Troubleshooting Essentials, University Edition (2026), §6.1 and Fig 6.1, §6.2, §7.3, §11.1
